Das U-Boot

U-Boot is both a first-stage and second-stage bootloader. It is loaded by the system's ROM (e.g. on-chip ROM of the ARM CPU) from a supported boot device, such as an SD card, SATA drive, NOR flash (e.g. using SPI or I²C), or NAND flash. If there are size constraints, U-Boot may be split into two stages: the platform would load a small SPL (Secondary Program Loader), which is a stripped-down version of U-Boot, and the SPL would do some initial hardware configuration (e.g. DRAM initialization using CPU cache as RAM) and load the larger, fully featured version of U-Boot.[3][4][5] Regardless of whether the SPL is used, U-Boot performs both first-stage (e.g., configuring memory controllers and SDRAM) and second-stage booting (performing multiple steps to load a modern operating system from a variety of devices that must be configured, presenting a menu for users to interact with and control the boot process, etc.).

U-Boot implements a subset of the UEFI specification as defined in the Embedded Base Boot Requirements (EBBR) specification.[6] UEFI binaries like GRUB or the Linux kernel can be booted via the boot manager or from the command-line interface.

U-Boot runs a command-line interface on a console or a serial port. Using the CLI, users can load and boot a kernel, possibly changing parameters from the default. There are also commands to read device information, read and write flash memory, download files (kernels, boot images, etc.) from the serial port or network, manipulate device trees, and work with environment variables (which can be written to persistent storage, and are used to control U-Boot behavior such as the default boot command and timeout before auto-booting, as well as hardware data such as the Ethernet MAC address).

Unlike PC bootloaders which obscure or automatically choose the memory locations of the kernel and other boot data, U-Boot requires its boot commands to explicitly specify the physical memory addresses as destinations for copying data (kernel, ramdisk, device tree, etc.) and for jumping to the kernel and as arguments for the kernel. Because U-Boot's commands are fairly low-level, it takes several steps to boot a kernel, but this also makes U-Boot more flexible than other bootloaders, since the same commands can be used for more general tasks. It's even possible to upgrade U-Boot using U-Boot, simply by reading the new bootloader from somewhere (local storage, or from the serial port or network) into memory, and writing that data to persistent storage where the bootloader belongs.

U-Boot has support for USB, so it can use a USB keyboard to operate the console (in addition to input from the serial port), and it can access and boot from USB Mass Storage devices such as SD card readers.

U-Boot on the Openmoko Freerunner

U-Boot on the XPedite5501

The project's origin is a 8xx PowerPC bootloader called 8xxROM written by Magnus Damm.[7] In October 1999 Wolfgang Denk moved the project to SourceForge.net and renamed it to PPCBoot, because SF.net did not allow project names starting with digits.[7] Version 0.4.1 of PPCBoot was first publicly released July 19, 2000.

In 2002 a previous version of the source code was briefly forked into a product called ARMBoot, but was merged back into the PPCBoot project shortly thereafter. On October 31, 2002 PPCBoot−2.0.0 was released. This marked the last release under the PPCBoot name, as it was renamed to reflect its ability to work on other architectures besides the PPC ISA.[8][9]

PPCBoot−2.0.0 became U−Boot−0.1.0 in November 2002, expanded to work on the x86 processor architecture. Additional architecture capabilities were added in the following months: MIPS32 in March 2003, MIPS64 in April, Nios II in October, ColdFire in December, and MicroBlaze in April 2004. The May 2004 release of U-Boot-1.1.2 worked on the products of 216 board manufacturers across the various architectures.[9]

The current name Das U-Boot adds a German definite article, to create a bilingual pun on the classic 1981 German submarine film Das Boot, which takes place on a World War II German U-boat. It is free software released under the terms of the GNU General Public License. It can be built on an x86 PC for any of its intended architectures using a cross development GNU toolchain, for example crosstool, the Embedded Linux Development Kit (ELDK) or OSELAS.Toolchain.

The importance of U-Boot in embedded Linux systems is quite succinctly stated in the book Building Embedded Linux Systems, by Karim Yaghmour, whose text about U-Boot begins, "Though there are quite a few other bootloaders, 'Das U-Boot', the universal bootloader, is arguably the richest, most flexible, and most actively developed open source bootloader available."[10]

• The ARM-based Chromebooks ship with U-Boot. The Celeron- and i5-based Chromebooks use it as payload for coreboot.[11]
• The PowerPC based series of AmigaOne computers running AmigaOS use U-Boot, in particular the Sam440ep and Sam460ex by ACube Systems Srl, and the AmigaOne X5000 by A-Eon, the successor of the AmigaOne X1000.
• Ubiquiti Networks devices use U-Boot.
• Amazon Kindle & Kobo eReader devices use U-Boot as their bootloader.
• TP-Link and several other OpenWRT/LEDE compatible MIPS based wireless routers use U-Boot for bootloading.
• Teltonika cellular routers use bootloader based on U-Boot.
• SpaceX's Falcon and Dragon both use U-Boot.[12]
• Asahi Linux uses it as payload for m1n1 in order to boot Linux on Apple Silicon Mac.[13]

• Comparison of boot loaders
• RedBoot
• Coreboot
• Barebox

• /Official website
• Official Git repository
• Barebox (formerly known as U-Boot-V2)
• ARMboot