SILLIAC

The SILLIAC (Sydney version of the Illinois Automatic Computer, i.e. the Sydney ILLIAC), an early computer built by the University of Sydney, Australia, was based on the ILLIAC and ORDVAC computers developed at the University of Illinois.

SILLIAC being serviced by Peter Aplin of Sydney University

Like other early computers, SILLIAC was physically large. The computer itself was a single large cabinet 2.5 m high, 3 m wide and 0.6 m deep in one room. Its power supply occupied a second room and air conditioning required an additional room in the basement.

It ran until May 17, 1968, when it was replaced by a faster and bigger machine. Although it was then broken up, some pieces of SILLIAC are at the Powerhouse Museum and others are displayed at Sydney University.

History

SILLIAC[1] had its genesis in late 1953 when Harry Messel, the dynamic new head of the School of Physics, and John Blatt, newly arrived researcher, both independently realised that the School needed an electronic computer as a tool for theoretical physics. Whilst the first computer in the southern hemisphere, the CSIR Mk 1, was already running elsewhere on the University of Sydney grounds, there were several serious impediments to its use by the School of Physics: The CSIR Mk 1 was fully occupied with CSIR research and John Blatt found its staff very unhelpful; and, as a serial architecture computer, it was far too slow for the sort of problems that Blatt and Messel envisaged. The solution was for the School to build its own computer.

Rather than design a computer from scratch, Blatt and Messel chose to copy the design of the ILLIAC for which the University of Illinois were happy to provide plans and assistance. John Algie, then maintenance engineer for CSIRAC, estimated the cost at AU£35,200, which was approximately ten times the cost of a Sydney suburban house at the time.[2] Based on this, a decision to proceed was made at the end of 1953. A mutual friend introduced Messel to Adolph Basser,[3] who donated AU£50,000 towards the computer.[4][5] SILLIAC's eventual cost was AU£75,000.[2]

In July 1954, Standard Telephones and Cables was contracted to build the computer, with testing and installation performed by technicians within the School of Physics.

SILLIAC's first scientific computation was carried out by PhD student Bob May (later Robert May, Baron May of Oxford) in June 1956,[2] after self tests had been completed successfully. Users were provided with regular access from July 9, with the official opening conducted on September 12.

Barry de Ferranti, a pioneer involved in the construction of SILLIAC described the main cabinet of the computer as about 2 metres high, 1 metre deep and 5 metres long with glass panels at the front and light switches that indicated what was going on inside.

It ran until May 17, 1968, when it was replaced by a faster and bigger machine. SILLIAC has now been broken up into pieces with parts of it placed on display in the Chau Chak Wing Museum,[2] which opened in November 2020.[6]

Hardware specifications
  • Parallel, asynchronous operation. Approximately 13,000 adds, 1400 multiplies or 1200 divides per second
  • Memory: 1024 words of 40 bits using 40 Williams tubes
  • Two 20-bit instructions per word.
  • Approximately 150 operations on 2 registers
  • Paper tape input at 200 characters per second (cps),[7] paper tape output at about 50 cps or teleprinter output at 10 cps. Four magnetic tape units added in 1958
  • Initially 2768 valves. Increased to 2911 during 1958 upgrade
  • Power consumption: 35 kW
  • Average of 11 hours between failures

Like most of the IAS family, SILLIAC was not an exact copy of ILLIAC. One important change was the use of 2C51[8] valves in place of the more common 6J6.[9] The 2C51 had been developed by Bell Labs for use in undersea telephone repeaters and had about 5 times the life (for 6 times the cost). This decision significantly improved the reliability of SILLIAC compared to its contemporaries.

Conservation

Some pieces of SILLIAC are at the Powerhouse Museum and others are displayed at Sydney University.[10]

In March 2008, the Australian Computer Museum Society was seeking alternative storage, or risked its collection, including important components of SILLIAC, being scrapped.[11]

In 2023 the Australian Computer Museum Society now has a venue for displaying the parts of SILLIAC that are in its collection.

See also

References
  1. Deane, John (2006). SILLIAC – Vacuum Tube Supercomputer. Sydney: Science Foundation for Physics within the University of Sydney, in association with the Australian Computer Museum Society. ISBN 9781864878448.
  2. Dodd, George (5 May 2021). "The Machine that Advanced Australia into the Computer Age: SILLIAC". Sydney Alumni Magazine. No. 13. The University of Sydney. pp. 24–25. Retrieved 11 June 2021.
  3. Rutledge, Martha; Lemon, Andrew (1993). "Basser, Sir Adolph (1887–1964)". Australian Dictionary of Biography. Vol. 13. Melbourne University Press. Retrieved 18 October 2018.
  4. Ji, Julie (5 September 2006). "Celebrating 50 years of computers at Sydney". University of Sydney News. The University of Sydney. Archived from the original on 30 October 2007. Retrieved 18 October 2018.
  5. Jacobs, Marie (Winter 2006). "Love at First Byte" (PDF). Sydney Alumni Magazine. The University of Sydney. pp. 12–15. Retrieved 18 October 2018.
  6. "Sydney's newest museum opens". University of Sydney News. The University of Sydney. 16 November 2020. Retrieved 11 June 2021.
  7. 'The Electronic Computer "SILLIAC" ', The Nuclear Research Foundation, Sydney, September 1956.
  8. 2C51 Medium-Mu Twin Triode Archived 2007-09-28 at the Wayback Machine, 9 pins, 2.2W heater
  9. 6J6 Medium-Mu Twin Triode Archived 2006-09-27 at the Wayback Machine, 7 pins, 2.8W heater
  10. The Age - Computer that launched a revolution - Louisa Hearn - 12 September 2006
  11. Heritage computers facing scrap heap, ABC Online, 14 March 2008, accessed 15 March 2008
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.