Penryn (microprocessor)

Wikinews has related news:

• Intel launches 45nm "Penryn" processor aiming for energy-efficiency

The successor to the Merom core for the Core 2 Duo T5000/T7000 series mobile processors, code-named Penryn, debuted on the 45 nanometer process. Many details about Penryn appeared at the April 2007 Intel Developer Forum. Intel's new 45 nm Penryn-based Core 2 Duo and Core 2 Extreme processors were released on January 6, 2008. The new processors launched exclusively with a TDP of 35 W; later releases were more energy efficient. HP began to offer the first model, the T9500, from late January 2008.[2] The T9500 offered a 2.6 GHz clock rate, higher than all but the Extreme Edition of the Merom range, and 6 MB (rather than 4 MB) of Level 2 Cache.

Important advances[3] included the addition of new instructions including SSE4 (also known as Penryn New Instructions) and new fabrication materials; most significantly a hafnium-based high-k dielectric.

All SL9xxx, SP9xxx, P9xxx, T9xxx and X9xxx processors are Penryn with the full 6 MB L2 cache enabled, while P7xxx, P8xxx and T8xxx can be either Penryn-3M or Penryn with only 3 MB cache enabled. They are indistinguishable by software, but Penryn uses product code 80576.

Intel released an Apple-only Exxx chip on April 28, 2008 that increased the clock rate to 3.06 GHz as well as increasing the Front Side Bus to 1066 MT/s, and changed the Cache to 6 MB shared L2. While it is used in desktop computers and has an E8xxx name, it uses the same packaging as mobile CPUs and is therefore considered a Penryn and not Wolfdale.

On desktops, Penryn pairs with the 2007 desktop Bearlake[4] chipset series, some of whose models include an increase in bus performance (connection to the northbridge, etc.) to 1333 MT/s and support for DDR3 SDRAM. In notebooks and other mobile equipment, Penryn initially paired with the mobile Crestline chipset series which supports DDR2 but not DDR3, (although when Penryn was released, Intel believed[5] future DDR3 support would benefit mobile equipment's power- and heat-constrained environments). Mobile Penryns were later paired with the Cantiga chipset series which (among other enhancements) added DDR3 support.

Celeron 900

The smaller (82 mm² instead of 107 mm²) Penryn-3M is used in mobile processors with an L2 Cache 3 MB or less as a successor to Merom-2M. Its product code is 80577. The entry level Penryn-3M Core 2 processor is the T6xxx series, with 2 MB L2 Cache and begins with the T6400 at a clock rate of 2 GHz. Other Penryn-3M based processor series are Celeron T3xxx, Pentium T4xxx, as well as most Core 2 Duo SU9xxx, P7xxx, P8xxx, T8xxx processors.

In September 2009, Intel introduced new Consumer Ultra-Low Voltage processors based on Penryn-3M, as Celeron SU2xxx series, Pentium SU4xxx series and Core 2 Duo SU7xxx series, with 1, 2 and 3 MB of active L2 cache. Like the earlier Core 2 Duo SU9xxx series, they are always soldered on using a BGA956 package and have a TDP of only 10 W.

Penryn-L does not actually seem to be a separate chip but only a version of Penryn-3M with a single core enabled. However, it has a separate product code of 80585. Penryn-L is used in the ultra-low voltage Core 2 SU3xxx, the standard voltage Celeron 9xx and the CULV Celeron 7xx and Pentium SU2xxx series. The Celeron versions have only 1 MB active L2 cache, Pentium versions have 2 MB.

In August 2008 Intel released their first two quad-core processors for notebooks, the Core 2 Quad Q9100 and Core 2 Extreme QX9300.[6] As these require more power (45 W) and cooling than other Penryn processors they are not automatically compatible with all Centrino 2 notebooks. Also the Extreme version requires the GS45/GM45/PM45 chipset.